- 您现在的位置：买卖IC网 > Sheet目录1214 > EVAL-ADUM3221AEBZ (Analog Devices Inc)BOARD EVAL FOR ADUM3220/ADUM3221
ADuM3220/ADuM3221
APPLICATIONS INFORMATION
PC BOARD LAYOUT
The ADuM3220 / ADuM3221 digital isolators require no exter-
nal interface circuitry for the logic interfaces. Power supply
bypassing is required at the input and output supply pins, as
shown in Figure 19. Use a small ceramic capacitor with a value
from 0.01 μF to 0.1 μF to provide a good high frequency bypass.
On the output power supply pin, V DD2 , it is recommended that a
10 μF capacitor also be added to provide the charge required to
drive the gate capacitance at the ADuM3220 / ADuM3221 outputs.
On the output supply pin, the use of vias with the bypass capacitor
should be avoided, or multiple vias should be used to reduce the
inductance in the bypassing. The total lead length between both
ends of the smaller capacitor and the input or output power
supply pin should not exceed 20 mm.
V DD1 V DD2
V IA V OA
V IB V OB
GND 1 GND 2
Figure 19. Recommended PCB Layout
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes a
logic signal to propagate through a component. The propagation
Data Sheet
THERMAL LIMITATIONS AND SWITCH LOAD
CHARACTERISTICS
For isolated gate drivers, the necessary separation between the
input and output circuits prevents the use of a single thermal pad
beneath the part; therefore, heat is dissipated mainly through
the package pins.
Package thermal dissipation limits the performance of switching
frequency vs. output load, as illustrated in Figure 8, which shows
the maximum load capacitance that can be driven with a 1 ? series
gate resistor for different values of output voltage. For example,
this curve shows that a typical ADuM3220 / ADuM3221 can drive
a large MOSFET with 120 nC gate charge at 8 V output (which is
equivalent to a 15 nF load) up to a frequency of about 300 kHz.
OUTPUT LOAD CHARACTERISTICS
The ADuM3220 / ADuM3221 output signals depend on the
characteristics of the output load, which is typically an N-channel
MOSFET. The driver output response to an N-channel MOSFET
load can be modeled with a switch output resistance (R SW ), an
inductance due to the printed circuit board trace (L TRACE ), a series
gate resistor (R GATE ), and a gate-to-source capacitance (C GS ), as
delay to a logic low output can differ from the propagation delay
to a logic high output. The ADuM3220 / ADuM3221 specify t DLH
as the time between the input rising high logic threshold, V IH ,
and the output rising 10% threshold (see Figure 20). Likewise, the
V IA
ADuM3220/
ADuM3221
V OA R SW
R GATE
L TRACE
C GS
V O
falling propagation delay, t DHL , is defined as the time between the
input falling logic low threshold, V IL , and the output falling 90%
threshold. The rise and fall times are dependent on the loading
conditions and are not included in the propagation delay, as is
the industry standard for gate drivers.
Figure 21. RLC Model of the Gate of an N-Channel MOSFET
driver output, which is about 1.5 ?. R GATE is the intrinsic gate
resistance of the MOSFET and any external series resistance. A
MOSFET that requires a 4 A gate driver has a typical intrinsic
OUTPUT
INPUT
90%
10%
V IH
V IL
gate resistance of about 1 ? and a gate-to-source capacitance,
C GS , from 2 nF to 10 nF. L TRACE is the inductance of the printed
circuit board trace, typically a value of 5 nH or less for a well-
designed layout with a very short and wide connection from the
The following equation defines the Q factor of the RLC circuit,
which indicates how the ADuM3220 / ADuM3221 output responds
to a step change. For a well-damped output, Q is less than 1.
t DLH
t DHL
Adding a series gate resistor dampens the output response.
t R t F
Figure 20. Propagation Delay Parameters
Q =
( R SW
1
+ R GATE )
×
L TRACE
C GS
Channel-to-channel matching refers to the maximum amount
that the propagation delay differs between channels within a
single ADuM3220 / ADuM3221 component.
Propagation delay skew refers to the maximum amount that
In Figure 5 and Figure 6, the ADuM3220 / ADuM3221 output
waveforms for 10 V output are shown for a C GS of 2 nF and 1 nF,
respectively. Note the ringing of the output in Figure 6 with C GS
of 1 nF and a calculated Q factor of 1.5, where less than 1 is
desired for good damping.
ADuM3221 components operating under the same conditions.
Rev. C | Page 12 of 16
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
EVAL-ADUM3471EBZ
EVALUATION MODULE FOR ADUM3471
EVAL-ADUM4160EBZ
EVALUATION MODULE FOR ADUM4160
EVAL-ADUM4223AEBZ
BOARD EVAL FOR ADUM4223
EVAL-ADUMQSEBZ
EVAL BOARD FOR ICOUPLER SMD
EVAL-ADUSB2EBUZ
BOARD EVAL USBI
EVAL-ADV7195EB
BOARD EVAL FOR ADV7195
EVAL-ADV7401EBZ
BOARD EVALUATION FOR ADV7401
EVAL-ADV7403EBZ
BOARD EVALUATION FOR ADV7403
相关代理商/技术参数
EVAL-ADUM3223AEBZ
功能描述:BOARD EVAL FOR ADUM3223 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:iCoupler® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
EVAL-ADUM330X
制造商:AD 制造商全称:Analog Devices 功能描述:Quad Isolators with isoPower Evaluation Board
EVAL-ADUM340X
制造商:AD 制造商全称:Analog Devices 功能描述:Quad Isolators with isoPower Evaluation Board
EVAL-ADUM3471EBZ
功能描述:EVALUATION MODULE FOR ADUM3471 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:iCoupler® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
EVAL-ADUM3481EBZ
制造商:Analog Devices 功能描述:EVALUATION BOARD DIGITAL ISOLATOR - Boxed Product (Development Kits)
EVAL-ADUM4070EBZ
功能描述:界面开发工具 RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
EVAL-ADUM4160EBZ
功能描述:EVALUATION MODULE FOR ADUM4160 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:iCoupler® 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADUM4160EBZ RENT
制造商:Analog Devices 功能描述:BOARD EVAL DIGITAL ISOLATOR